Research Article

Investigating Effect of Bearing Length on Tensile Strength of 1045 Steel in Wire Drawing Operation

Volume: 23 Number: 4 December 3, 2020
Kahramanmaras Sutcu Imam University Journal of Engineering Sciences Cover
Kahramanmaras Sutcu Imam University Journal of Engineering Sciences
PDF Download
TR EN

Investigating Effect of Bearing Length on Tensile Strength of 1045 Steel in Wire Drawing Operation

Abstract

In this work, effect of bearing length on tensile strength was investigated. The influence of the bearing length is illustrated using two different reduction ratios and wire diameters. According to the results, the increase in strength was observed as the length of the bearing zone increased. However, the long bearing length caused various manufacturing problems during production. Microhardness distributions in wire cross section, on the other hand, increased as the length of bearing increased. The main reason for the increase of microhardness is the deformation hardening caused by the high friction force obtained by increasing the bearing length.

Keywords

References

  1. Gillström, P., & Jarl, M. (2007). Wear of die after drawing of pickled or reverse bent wire rod. Wear, 262(7–8), 858–867. https://doi.org/10.1016/j.wear.2006.08.016
  2. Korchunov, A., Gun, G., & Polyakova, M. (2014). Recovery effect in drawing of steel bar for sizing. Procedia Engineering, 81, 676–681. https://doi.org/10.1016/j.proeng.2014.10.059
  3. Nilsson, M., & Olsson, M. (2011). Tribological testing of some potential PVD and CVD coatings for steel wire drawing dies. Wear, 273(1), 55–59. https://doi.org/10.1016/j.wear.2011.06.020
  4. Sas-Boca, I. M., Tintelecan, M., Pop, M., Iluţiu-Varvara, D. A., & Mihu, A. M. (2017). The Wire Drawing Process Simulation and the Optimization of Geometry Dies. Procedia Engineering, 181, 187–192. https://doi.org/10.1016/j.proeng.2017.02.368
  5. Schade, P. (2006). Wire drawing failures and tungsten fracture phenomena. International Journal of Refractory Metals and Hard Materials, 24(4), 332–337. https://doi.org/10.1016/j.ijrmhm.2005.09.003
  6. Wei, D., Min, X., Hu, X., Xie, Z., & Fang, F. (2020). Microstructure and mechanical properties of cold drawn pearlitic steel wires: Effects of drawing-induced heating. Materials Science and Engineering A, 784, 139341. https://doi.org/10.1016/j.msea.2020.139341
  7. Xu, P., Liang, Y., Li, J., & Meng, C. (2019). Further improvement in ductility induced by the refined hierarchical structures of pearlite. Materials Science and Engineering A, 745, 176–184. https://doi.org/10.1016/j.msea.2018.12.069

Details

Primary Language

English

Subjects

Mechanical Engineering

Journal Section

Research Article

Authors

Publication Date

December 3, 2020

Submission Date

August 25, 2020

Acceptance Date

September 10, 2020

Published in Issue

Year 2020 Volume: 23 Number: 4

DOI

https://doi.org/10.17780/ksujes.784544

IZ

https://izlik.org/JA43SK98LA

Cite

RIS / Bibtex
APA
Çelik, E., Özen, F., İlhan, E., & Aslanlar, S. (2020). Investigating Effect of Bearing Length on Tensile Strength of 1045 Steel in Wire Drawing Operation. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi, 23(4), 227-235. https://doi.org/10.17780/ksujes.784544