THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115

Mustafa Kuntoğlu; Abdullah Aslan; Rüstem Binali; Zeynep Sude Şalvarcıoğlu

TR EN

AISI 5115 ALAŞIMININ SERT TORNALAMA İŞLEMİNDE, YARI KURU VE KURU YAĞLAMA ORTAMLARININ YÜZEY PÜRÜZLÜLÜĞÜ VE DİĞER İŞLENEBİLİRLİK GÖSTERGELERİ ÜZERİNDEKİ ETKİLERİ

Öz

AISI 5115 çeliği, mukavemeti ve aşınma direnci sayesinde makinelerde yaygın olarak kullanılan sertleştirilmiş düşük alaşımlı bir çelik türüdür. Bu tür yüzey sertleştirilmiş malzemelerin işlenmesi, yüksek kesme kuvvetleri, takım aşınması ve sertlikten kaynaklanan düşük yüzey kalitesi sorunları nedeniyle zorluklar sunmaktadır. Bu nedenle, kesme ortamının seçimi bu noktada kritik öneme sahiptir ve özellikle kuru veya Minimum Miktarda Yağlama (MMY) yöntemi, çevresel avantajları ve artan enerji verimliliği ile son yıllarda ön plana çıkmıştır. Bu çalışma, sertleştirilmiş AISI 5115 çeliklerinin tornalanması sırasında MMY ve kuru ortam koşullarının yüzey pürüzlülüğü, kesme kuvvetleri ve enerji tüketimi üzerindeki etkilerini deneysel olarak araştırmaktadır. Tornalama koşulları kuru olup, MQL için bitkisel bazlı yağ kullanılmıştır. MMY uygulamasının yüzey pürüzlülüğünü azalttığı, daha yüksek kaliteli yüzeyler sağladığı, kesme kuvvetlerini azalttığı ve enerji tüketimini optimize ettiği belirlenmiştir. Bu çalışmanın yeniliği, enerji tüketimi, kesme kuvvetleri ve yüzey kalitesi de dahil olmak üzere 5115 alaşımlı çeliğin çevresel ve işlenebilirlik faktörlerinin kapsamlı bir analizini sunmasıdır.

Anahtar Kelimeler

THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115

Öz

AISI 5115 steel is a type of hardened low-alloy steel widely used in machinery due to its strength and wear resistance. Machining of such case-hardened materials presents challenges due to high cutting forces, tool wear, and low surface quality issues resulting from hardness. Therefore, the selection of the cutting medium is critical at this point, and near-dry or MQL method in particular has come to the forefront in recent years with its environmental advantages and increased energy efficiency. This study experimentally investigates the influences of MQL and dry environment conditions on surface roughness, cutting forces, and energy consumption during the turning of hardened AISI 5115 steels. Turning conditions are dry, and MQL used vegetable based oil. It was determined that the MQL application reduces surface roughness, provides higher quality surfaces, reduces cutting forces, and optimizes energy consumption. The novelty of this study is a comprehensive analysis of the environmental and machinability factors of the 5115 alloy steel by including energy consumption, cutting forces, and surface quality.

Anahtar Kelimeler

Kaynakça

Abukhshim, N., Mativenga, P., & Sheikh, M. A. (2006). Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining. International Journal of Machine Tools and Manufacture, 46(7-8), 782-800. https://doi.org/10.1016/j.ijmachtools.2005.07.024
Amini, K., Araghi, A., & Akhbarizadeh, A. (2015). Effect of deep cryogenic heat treatment on the wear behavior of carburized DIN 1.7131 grade steel. Acta Metallurgica Sinica (English Letters), 28(3), 348-353. https://doi.org/10.1007/s40195-015-0204-1
Aslan, A. (2020). Optimization and analysis of process parameters for flank wear, cutting forces and vibration in turning of AISI 5140: A comprehensive study. Measurement, 163, 107959. https://doi.org/10.1016/j.measurement.2020.107959
Aslan, A., & Salur, E. (2022). Applications of nanofluids in minimum quantity lubrication machining: A review. Nanomaterials in manufacturing processes, 53-84.
Aslan, A., Salur, E., & Kuntoğlu, M. (2022). Evaluation of the role of dry and MQL regimes on machining and sustainability index of Strenx 900 steel. Lubricants, 10(11), 301. https://doi.org/10.3390/lubricants10110301
Bennett, J. M. (1992). Recent developments in surface roughness characterization. Measurement Science and Technology, 3(12), 1119. 10.1088/0957-0233/3/12/001
Binali, R. (2024). Experimental and machine learning comparison for measurement the machinability of nickel based alloy in pursuit of sustainability. Measurement, 236, 115142. https://doi.org/10.1016/j.measurement.2024.115142
Binali, R., Demirpolat, H., Kuntoğlu, M., & Kaya, K. Exploring the Tribological Performance of Mist Lubrication Technique on Machinability Characteristics During Turning S235JR Steel. Manufacturing Technologies and Applications, 5(3), 276-283. https://doi.org/10.52795/mateca.1541090

Binali, R., Korkmaz, M. E., Özdemir, M. T., & Günay, M. (2025). A Holistic Perspective on Sustainable Machining of Al6082: Synergistic Effects of Nano-Enhanced Bio-Lubricants. Machines, 13(4). https://doi.org/10.3390/machines13040293
Cui, S. a., Liu, P., Li, Z., Xu, X., & Ju, J. W. (2020). Shotcrete performance-loss due to seepage and temperature coupling in cold-region tunnels. Construction and Building Materials, 246, 118488. https://doi.org/10.1016/j.conbuildmat.2020.118488
Demirpolat, H. (2024). Evaluation of the turning parameters of AISI 5115 steel in dry and MQL cutting environments with the use of a coated carbide cutting insert: An experimental study. Journal of Materials and Mechatronics: A, 5(1), 168-182. https://doi.org/10.55546/jmm.1488880
Demirpolat, H., Kaya, K., Binali, R., & Kuntoğlu, M. (2023). AISI 52100 Rulman Çeliğinin Tornalanmasında İşleme Parametrelerinin Yüzey Pürüzlülüğü, Kesme Sıcaklığı ve Kesme Kuvveti Üzerindeki Etkilerinin İncelenmesi. İmalat Teknolojileri ve Uygulamaları, 4(3), 179-189. https://doi.org/10.52795/mateca.1393430
Frölich, D., Magyar, B., Sauer, B., Mayer, P., Kirsch, B., Aurich, J., . . . Eifler, D. (2015). Investigation of wear resistance of dry and cryogenic turned metastable austenitic steel shafts and dry turned and ground carburized steel shafts in the radial shaft seal ring system. Wear, 328, 123-131. https://doi.org/10.1016/j.wear.2015.02.004
Gangopadhyay, S., Acharya, R., Chattopadhyay, A. K., & Sargade, V. G. (2010). Effect of cutting speed and surface chemistry of cutting tools on the formation of BUL or BUE and surface quality of the generated surface in dry turning of AA6005 aluminium alloy. Machining Science and Technology, 14(2), 208-223. https://doi.org/10.1080/10910344.2010.500961
Gupta, M. K., & Sood, P. (2017). Surface roughness measurements in NFMQL assisted turning of titanium alloys: An optimization approach. Friction, 5(2), 155-170. https://doi.org/10.1007/s40544-017-0141-2
Hosseini, S. R. E., Khosravi, H., Sohrabi, R., Hosseini, Z., Karimi, E. Z., & Makarem, M. (2013). Correlation between hardenability curves and microstructure of a cementation steel carburized in the presence of Na2CO3 as an energizer material. ISIJ international, 53(12), 2213-2217. https://doi.org/10.2355/isijinternational.53.2213
Jafar, R., Hadavi, V., Spelt, J., & Papini, M. (2016). Dust reduction in abrasive jet micro-machining using liquid films. Powder technology, 301, 1270-1274. https://doi.org/10.1016/j.powtec.2016.08.002
Korkmaz, M. E., & Gupta, M. K. (2024). A state of the art on cryogenic cooling and its applications in the machining of difficult-to-machine alloys. Materials, 17(9), 2057. https://doi.org/10.3390/ma17092057
Kul, B. S., & Yamaner, A. S. A Comparative Evaluation of Dry-MQL Turning Applications for AISI 5115 Steel. Manufacturing Technologies and Applications, 6(1), 23-32. https://doi.org/ 10.52795/mateca.1571978
Kumar, R., Bilga, P. S., & Singh, S. (2017). Multi objective optimization using different methods of assigning weights to energy consumption responses, surface roughness and material removal rate during rough turning operation. Journal of cleaner production, 164, 45-57. https://doi.org/10.1016/j.jclepro.2017.06.077
Kuntoğlu, M., Aslan, A., Pimenov, D. Y., Giasin, K., Mikolajczyk, T., & Sharma, S. (2020). Modeling of cutting parameters and tool geometry for multi-criteria optimization of surface roughness and vibration via response surface methodology in turning of AISI 5140 steel. Materials, 13(19), 4242. https://doi.org/10.3390/ma13194242
Kuntoğlu, M., Aslan, A., Pimenov, D. Y., Usca, Ü. A., Salur, E., Gupta, M. K., . . . Sharma, S. (2020). A review of indirect tool condition monitoring systems and decision-making methods in turning: Critical analysis and trends. Sensors, 21(1), 108. https://doi.org/10.3390/s21010108
Kuntoğlu, M., Aslan, A., Sağlam, H., Pimenov, D. Y., Giasin, K., & Mikolajczyk, T. (2020). Optimization and analysis of surface roughness, flank wear and 5 different sensorial data via tool condition monitoring system in turning of AISI 5140. Sensors, 20(16), 4377. https://doi.org/10.3390/s20164377
Lingnau, L. A., & Walther, F. (2023). Characterization and separation of damage mechanisms of extruded case-hardening steel AISI 5115 under cyclic axial-torsional loading. Paper presented at the Materials Science Forum. https://doi.org/10.4028/p-kJ0mH5
Makhesana, M. A., Patel, K., Ghetiya, N., Binali, R., & Kuntoğlu, M. (2024). Evaluation of drilling and hole quality characteristics in green machining aluminium alloys: A new approach towards green machining. Journal of Manufacturing Processes, 129, 176-186. https://doi.org/10.1016/j.jmapro.2024.08.059
Mutlu, B., Binali, R., Demirsöz, R., & Yaşar, N. (2022). Machinability of CoCrMo alloy used in biomedical applications: investigation of cutting tool type. Gazi Journal of Engineering Sciences, 8(2), 215-227. 10.30855/gmbd.0705005
Nordgren, A., Samani, B. Z., & Saoubi, R. M. (2014). Experimental study and modelling of plastic deformation of cemented carbide tools in turning. Procedia CIRP, 14, 599-604. https://doi.org/10.1016/j.procir.2014.03.021
Oron, A., Davis, S. H., & Bankoff, S. G. (1997). Long-scale evolution of thin liquid films. Reviews of modern physics, 69(3), 931. https://doi.org/10.1103/RevModPhys.69.931
Özel, T., & Altan, T. (2000). Determination of workpiece flow stress and friction at the chip–tool contact for high-speed cutting. International Journal of Machine Tools and Manufacture, 40(1), 133-152. https://doi.org/10.1016/S0890-6955(99)00051-6
Öztürk, B., & Kara, F. (2020). Calculation and estimation of surface roughness and energy consumption in milling of 6061 alloy. Advances in Materials Science and Engineering, 2020(1), 5687951. https://doi.org/10.1155/2020/5687951
Park, K.-H., Olortegui-Yume, J., Yoon, M.-C., & Kwon, P. (2010). A study on droplets and their distribution for minimum quantity lubrication (MQL). International Journal of Machine Tools and Manufacture, 50(9), 824-833. https://doi.org/10.1016/j.ijmachtools.2010.05.001
Rech, J. (2006). Influence of cutting tool coatings on the tribological phenomena at the tool–chip interface in orthogonal dry turning. Surface and Coatings Technology, 200(16-17), 5132-5139. https://doi.org/10.1016/j.surfcoat.2005.05.032
Salur, E., Kuntoğlu, M., Aslan, A., & Pimenov, D. Y. (2021). The effects of MQL and dry environments on tool wear, cutting temperature, and power consumption during end milling of AISI 1040 steel. Metals, 11(11), 1674. https://doi.org/10.3390/met11111674
Shaikh, M. B. N., & Ali, M. (2021). Turning of steels under various cooling and lubrication techniques: a review of literature, sustainability aspects, and future scope. Engineering Research Express, 3(4), 042001. 10.1088/2631-8695/ac2e10
Shi, J., & Liu, C. R. (2005). On predicting softening effects in hard turned surfaces—Part I: Construction of material softening model. https://doi.org/10.1115/1.1948400
Shihab, S. K., Khan, Z. A., Mohammad, A., & Siddiquee, A. N. (2014). A review of turning of hard steels used in bearing and automotive applications. Production & Manufacturing Research, 2(1), 24-49. https://doi.org/10.1080/21693277.2014.881728
Song, X., He, W., & Ihara, T. (2016). Predicting periodic evolution of BUE formation mechanisms during machining ductile material using damage mechanics. Mechanical Engineering Journal, 3(6), 15-00534-00515-00534. 10.1299/mej.15-00534
Yaqoob, S., Ghani, J. A., Juri, A. Z., Muhamad, S. S., Haron, C. H. C., & Jouini, N. (2024). A review of sustainable hybrid lubrication (Cryo-MQL) techniques in machining processes. The International Journal of Advanced Manufacturing Technology, 131(1), 151-169. https://doi.org/10.1007/s00170-024-13135-4

Ayrıntılar

Birincil Dil

İngilizce

Konular

Makine Mühendisliğinde Optimizasyon Teknikleri, Makine Mühendisliği (Diğer)

Bölüm

Araştırma Makalesi

Yazarlar

Mustafa Kuntoğlu
0000-0002-7291-9468
Türkiye

Abdullah Aslan
0000-0001-8348-3471
Türkiye

Rüstem Binali ^*
0000-0003-0775-3817
Türkiye

Zeynep Sude Şalvarcıoğlu
0009-0009-0311-8032
Türkiye

Yayımlanma Tarihi

3 Haziran 2026

Gönderilme Tarihi

18 Aralık 2025

Kabul Tarihi

5 Mart 2026

Yayımlandığı Sayı

Yıl 2026 Cilt: 29 Sayı: 2

IZ

https://izlik.org/JA83DJ52ZK

Kaynak Göster

RIS / Bibtex

APA

Kuntoğlu, M., Aslan, A., Binali, R., & Şalvarcıoğlu, Z. S. (2026). THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi, 29(2), 699-708. https://izlik.org/JA83DJ52ZK

AMA

1.Kuntoğlu M, Aslan A, Binali R, Şalvarcıoğlu ZS. THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi. 2026;29(2):699-708. https://izlik.org/JA83DJ52ZK

Chicago

Kuntoğlu, Mustafa, Abdullah Aslan, Rüstem Binali, ve Zeynep Sude Şalvarcıoğlu. 2026. “THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115”. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi 29 (2): 699-708. https://izlik.org/JA83DJ52ZK.

EndNote

Kuntoğlu M, Aslan A, Binali R, Şalvarcıoğlu ZS (01 Haziran 2026) THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi 29 2 699–708.

IEEE

[1]M. Kuntoğlu, A. Aslan, R. Binali, ve Z. S. Şalvarcıoğlu, “THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115”, Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi, c. 29, sy 2, ss. 699–708, Haz. 2026, [çevrimiçi]. Erişim adresi: https://izlik.org/JA83DJ52ZK

ISNAD

Kuntoğlu, Mustafa - Aslan, Abdullah - Binali, Rüstem - Şalvarcıoğlu, Zeynep Sude. “THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115”. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi 29/2 (01 Haziran 2026): 699-708. https://izlik.org/JA83DJ52ZK.

JAMA

1.Kuntoğlu M, Aslan A, Binali R, Şalvarcıoğlu ZS. THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi. 2026;29:699–708.

MLA

Kuntoğlu, Mustafa, vd. “THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115”. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi, c. 29, sy 2, Haziran 2026, ss. 699-08, https://izlik.org/JA83DJ52ZK.

Vancouver

1.Mustafa Kuntoğlu, Abdullah Aslan, Rüstem Binali, Zeynep Sude Şalvarcıoğlu. THE INFLUENCES OF NEAR-DRY LUBRICATING AND DRY MEDIUMS ON SURFACE ROUGHNESS AND OTHER MACHINABILITY INDICATORS IN HARD TURNING AISI 5115. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi [Internet]. 01 Haziran 2026;29(2):699-708. Erişim adresi: https://izlik.org/JA83DJ52ZK